Mouse and keyboard failure
Mouse failure
(1) The system can not find the mouse
Analysis and diagnosis:
(1) Check the mouse and the host interface contacts are good. Mouse interface is carefully plugged in, restart the system.
(2) mouse in the line connection is bad, this failure is often seen in the mouse inside the wire with the circuit board connections. The solution is to open the mouse, use the electric iron solder joint welding can.
(3) There is a serial port may be burned, but this happens rarely, if the serial was burned out and had to replace a board.
(4) mouse cable wire disconnected. Use NP-FH100 Battery electric iron welding.
(2) abnormal mouse cursor or does not move
May dirt interrupt conflict or mouse. Interrupt resource problems can be solved by “6-1 Day” method; otherwise right mouse descaling processing.
(3) mouse button failures
Are mechanical failure. For the mouse button does not bounce, may be a fracture caused by the button below the contact switch in the bowl-shaped contact pads. Three-button mouse, you can remove the middle of a weld to meet urgent needs replaced, or can also be transplanted from a discarded mouse; the ability to click the switch bounce down, you can open the mouse, glue a mouse button in the following moderate thickness of the plastic sheet, and then install the mouse to normal use; I click the switch has been damaged, can be set to “right-handed” in the control panel mouse settings window (if you do not often use the right mouse button, then). However, you will feel when they are in operation very smoothly, it is best for a mouse.
Keyboard failure
Fault phenomenon: Sony laptop battery Keyboard Power On Self Test by typing A, S, D,, F, and V, I, O, P these two sets of keys not playing characters.
Analysis and processing: open the keyboard to see the transparent plastic circuit board, and many contacts. First check whether the key contact pressure together, everything is normal. Then a multimeter the contacts are pressed together can conduct electricity, everything is normal. Then check whether conductivity point of contact and the circuit board, or normal.
Carefully checked and found a circuit metal film out as part of the EOS 550D Battery Grip circuit is connected, look a little sparse. , Measured with a multimeter, the resistance is very large. May be due to the resistance of large electrical signals can not pass, but also happens to be that two sets of letter keys of the public line, so the key is the group not playing characters.
To plastic circuit connection is not a simple matter. Not electric iron welding, a welding, plastic will burn off. The first wire at both ends of the copper stripping out the two holes (be sure to avoid the bad section), available on both sides of the circuit resistance is also a small bar, wire stripping out copper wire to go through the hole, as tie circuit, the other end did the same. With a multimeter volume through! Fastened shell will also cushion some paper to prevent loosening. On machine one, everything is normal.
Inkjet printer common failure
This section introduced the EPSON 1500K printer, for example the treatment of the common faults of the inkjet printer.
Data and is out of paper light is flashing
A feed printer settings inconsistent with your actual feed method, the alignment of the.
(2) When loading paper, the printer does not accept. This problem lies in the switch of the check paper, due to prolonged use, the sensitivity of the check paper drop. Remove the back of the printer’s manual feed slot, it is easy to see the location of the check paper, it connected with the motherboard is a set of yellow lines, to remove it (using tweezers) with a multimeter testing, will be found check The paper switch is not flexible or disconnected. Rinse with alcohol or replaced, the problem can be solved.
Portable Solar Laptop Charger Data and the Pause light is flashing, or print the first hit in the head about
Analysis and treatment:
(1) This problem is primarily due to the prolonged use of a lot of debris (dust) between the print head and the guide rod, causing too much resistance. Turn off the printer, the guide rod clean with cotton dipped in absolute alcohol, coupled with the transformer oil or sewing machine oil, pull a few times about hand, can solve the problem.
(2) boot, the print head can not correctly positioning the SONY Camera Battery printer crash phenomenon. Can turn the printer off after a few seconds to boot, you can print normally.
All the indicator light flashes
This phenomenon, many users thought it was a printer to be a big problem, or that the quality of this printer. In fact, the contrary, this is it has the advantage, because the motherboard on the EPSON 1500K to a count of the chip is designed to calculate the number of paper, when the number of printed pages to achieve the specified number of print, the printer requires user waste cleaning, ink cartridges and chip count is cleared; or directly on the chip count is cleared (recommended not using).
Specific methods are as follows:
(1) print organs, remove the black ink cartridges;
(2) the scroll knob and remove the cutter;
Remove the control panel (panel in front of a clamp);
4 Remove the three screws around the (control panel), with a Battery Grip for Canon BG-E3 flat screwdriver to the printer the following clips Bankai; and then remove the lid, clamp the waste ink box of bubble wipe to remove water rinse and dry ;
(5) The above work is completed, will restore the printer, power. At this point you will see the failure phenomenon with the original, because you have not the counter is cleared. Press the switch – line feed / form feed – feed / back paper – micro adjustment of the right button, and then boot. When you hear the crisp voice instructions.
Print out the words distorted
The direct use of the software that comes with the printer calibration, and specific methods are as follows:
(1) hit the pause button and boot;
Load A4 paper to print The printer will print out two state of the current printer’s proofs (First To illustrate the method, the second calibration pattern Pattern 1). The two-page printed, the printer status lights for power. The observed calibration pattern is in the aligned position NO.1 to NO.25, from This NO.x start the calibration, when a NO.x vertical bar is not on time, and press the switch button until the indicator light to indicate the appropriate Pattern number. Print, print from your chosen NO.x start the calibration press the pause button, but the printer still print from the first root vertical bar. The printer will continuously print 7 Note: do not close the printer is printing. When you determine the final choice (page 7), turning off the printer power. Online and then print, if the word is still distorted, repeat the above steps until the correct date.
Also note that, before turning off the Aspire 5720 battery printer, make sure that the Pause light, because this is the printer a sign that the end of the mission, or that the non-normal shutdown, the next boot, the printer will clean the print head again, this will waste a lot of ink .
HP Deskjet 695C inkjet printer failure example
Fault phenomenon: the printer uses the past year, work has been normal. Third place can be when you print, always hit the paper, the print head will not move, reply to the indicator and power indicator light flashes alternately, Windows prompt “print head can not move the printer to jam.”
Analysis and Processing: Follow the prompts to open the printer cover, remove the paper, did not find a scrap of paper. Re-print, the fault remains. Began to suspect that there is a problem with the printer software, so re-install the printer software again, you can fault no excluded. When re-open the top cover of the printer, remove the paper and found that the printer used a fixed print head, so that the print head moves back and forth axis, has lost its past light, black, hand touch, friction. As the dust so that oil thickens, so that the shaft friction increase the printer’s print head movement difficult, so the printer report a paper jam.
Thus, with a cloth (note the cloth must not hair loss) and the shaft clean, preferably polished bright as ever, and then BlackBox 500S Receiver wipe the lubricant in the above, but do not impeccably too. After the above processing, the printer will not jam.
Final recommendations: the periodic inspection, regular activities in the inkjet printer parts to be cleaned regularly.